Custom kitchens built to code, on schedule, and on budget
Kitchen remodeling contractor Murphy TX
If your Murphy kitchen still has 1990s oak cabinets and a peninsula that blocks the cook, a kitchen remodeling contractor Murphy TX can change how the whole house flows. SpanForge Pro handles design, demolition, electrical, plumbing, and finish work under one licensed roof. We have served Collin County since 2022, and we pull permits, protect your floors, and clean up every night.
Live phone supportUpfront optionsBacked workmanship
What's included
What our kitchen remodeling service covers
A full kitchen remodel with SpanForge Pro covers demolition, structural changes, rough-in electrical and plumbing, drywall, paint, cabinets, countertops, tile, and appliance hookup. We pull the permits and schedule the inspections. Add-ons like new flooring beyond the kitchen, window replacement, or a tankless water heater are quoted separately so you can see the cost before you decide.
Demolition and haul-away
We remove old cabinets, counters, flooring, and any non-structural wall you want gone. Debris goes into a dumpster we place in your driveway, and we sweep the room at the end of each day. Floors and doorways get protected before the first swing of the sledgehammer.
Electrical and plumbing rough-in
New 20-amp small-appliance circuits, GFCI outlets near the sink, dedicated circuits for the microwave and disposal, and a 240-volt line for an electric range if needed. The plumber moves the drain and supply lines for a relocated sink or dishwasher, then we call for rough-in inspection.
Drywall, paint, and trim
We hang, tape, and texture drywall to match your existing walls, then paint before cabinets go in. Baseboard, shoe molding, and window trim are installed after the floor. You pick the color from Sherwin-Williams or Behr, and we buy it on our account.
Cabinets and countertops
Custom or semi-custom cabinets set level with a laser level, shimmed, and secured to studs found with a stud finder. Countertops are templated after cabinet set, then installed five to seven days later. We handle the delivery, receiving inspection, and damaged-box claims.
Tile and backsplash
Backsplash tile is laid with a laser level for a straight grout line, then grouted and sealed after 24 hours. Floor tile gets a crack-isolation membrane over plywood subfloor to prevent movement cracks. We cut around outlets cleanly and caulk the countertop seam.
Final trim and punch list
We install the disposal, dishwasher, faucet, and any new appliances, then test every circuit and supply line. You walk the room with the project lead, we write down anything you flag, and we finish the punch list before final payment. A one-year workmanship warranty covers our labor.
Service overview
What a kitchen remodeling contractor Murphy TX actually does
A kitchen remodeling contractor Murphy TX is a licensed general contractor that tears out old cabinets, countertops, flooring, and sometimes walls, then rebuilds the room to current code. That means new framing where a wall comes down, updated electrical for a 20-amp small-appliance circuit, fresh plumbing for the sink and dishwasher, and finished surfaces you actually want to look at. We handle the whole sequence: demolition, rough-in, inspection, drywall, paint, tile, cabinet set, and countertop template.
Murphy homes built in the 1990s and early 2000s are hitting the age where original cabinets sag, laminate counters delaminate, and outlets near the sink were never GFCI-protected. If you have been searching for a kitchen remodeler Murphy TX who will not disappear mid-job, we are the crew that shows up at 7 a.m. with a tape measure and a plan. We also fix the stuff you cannot see, like water damage behind the dishwasher or a stud finder confirming there is no header where you wanted one.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our kitchen remodeling process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Walk and measure
We spend 60 to 90 minutes in your kitchen measuring walls, checking the electrical panel, and looking under the sink for past leaks. You get a written scope and a fixed price, not a ballpark. If you want to move a gas line or take out a wall, we tell you right then whether it is structural and what the permit will cost.
Design and selections
You pick cabinets, countertops, tile, and paint. We give you a schedule that shows when each selection must be locked so the job does not stall. Most Murphy clients finalize cabinets and counters within two weeks. We handle the order, the delivery window, and the receiving inspection so damaged boxes get replaced before install day.
Demo and rough-in
We protect floors, shut off water, and tear out the old kitchen in one to two days. Then the electrician runs new circuits, the plumber moves the drain if needed, and we frame any new openings. The city inspector signs off on rough-in before insulation and drywall go back up. That inspection usually happens within 48 hours of our call.
Drywall, paint, and tile
Drywall gets hung, taped, and textured to match your existing walls. Paint goes on before cabinets so we are not cutting in around new boxes. Backsplash tile is set with a laser level and grouted after 24 hours. This stage runs seven to ten working days for a typical Murphy kitchen.
Cabinet set and punch list
We set cabinets level, shim the boxes, and install doors and drawers. Countertops get templated after cabinets are in, then installed five to seven days later. Final plumbing, electrical trim, and appliance hookup follow. We walk the room with you, write down anything you flag, and finish the punch list before final payment.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
DeWalt circular saw and Milwaukee cordless drill
Cutting plywood subfloor patches and driving cabinet screws. Cordless drills let us set boxes without dragging cords through your living room.
Laser level
Setting cabinet runs dead level and laying tile with a straight grout line. A laser level catches a sagging floor before the countertop template is taken.
Stud finder and tape measure
Locating studs for cabinet mounting and measuring the sixteenth-inch for custom boxes. Guessing here is how cabinets end up with filler strips.
Nail gun and sledgehammer
Framing headers and demo. The sledgehammer comes out on demo day, and the nail gun sets blocking for cabinet rails and drawer glides.
Concrete mixer
Mixing floor leveler when a Murphy slab has a low spot that would rock a cabinet or crack tile.
Makita and Stanley hand tools
Finish carpentry, trim work, and punch-list adjustments. We keep a full kit on site so we are not running to Home Depot or Lowe's mid-day.
Use cases
When Murphy homeowners call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Timber Ridge water damage repaired
A slow dishwasher leak had rotted the cabinet base and subfloor. The homeowner noticed a soft spot and a musty smell but did not know the source. Mold had started on the drywall behind the cabinet. → We pulled the cabinet, cut out the damaged subfloor and drywall, treated the mold, and rebuilt with plywood and moisture-resistant drywall. New cabinets, a new dishwasher, and a pressure-tested supply line went in. Total repair added three days to the schedule.
Willow Wood layout change for a double oven
The original kitchen had a single wall oven and a small island. The homeowner wanted a double oven, a larger island, and a dedicated circuit for a countertop microwave. The existing panel had no spare capacity. → We upgraded the panel, ran a 240-volt line for the double oven, added two 20-amp circuits, and built a larger island with an outlet on each end. The new cabinets and quartz counters were set with a laser level. The project finished in five weeks.
Problems we solve
Kitchen problems we fix in Murphy homes
Most Murphy kitchens we open up have at least one hidden issue. Here is what we run into and how we handle it without blowing your budget.
Water damage behind the dishwasher or sink
We pull the old cabinet, cut out the damaged drywall and subfloor, treat any mold, and rebuild with new plywood and moisture-resistant drywall. The repair is priced before we proceed, and we pressure-test the supply lines after the new sink goes in.
Outdated electrical wiring near the sink
We run new 20-amp small-appliance circuits, install GFCI outlets within six feet of the sink, and add dedicated lines for the microwave, disposal, and refrigerator. The city inspector signs off on rough-in before drywall closes the wall.
Sagging cabinets and delaminating counters
We replace the boxes with plywood-construction cabinets, set them level with a laser level, and template new quartz or granite countertops. Soft-close hinges and full-extension drawer glides come standard on our cabinet line.
A closed-off layout that blocks the cook
We confirm whether the wall is load-bearing, add a header if needed, and pull the structural permit. Then we build an island with a 36-inch aisle and run electrical for outlets on both ends. The room opens up without compromising the ceiling.
Pricing process
What kitchen remodeling costs in Murphy
$6,000 - $45,000 depending on scope
Layout changes
Moving a sink, range, or wall adds plumbing, electrical, and possibly structural work. A header for a removed wall can add $2,500 to $6,000. Keeping the layout saves the most money.
Cabinet grade
Stock boxes cost less but rarely fit a Murphy kitchen cleanly. Semi-custom and custom cabinets cost more but eliminate filler strips and give you the door style and finish you want. Expect $4,000 to $15,000 for the cabinet package.
Countertop material
Laminate is the cheapest, quartz and granite sit in the middle, and quartzite or marble run higher. A 40-square-foot kitchen typically costs $2,500 to $7,000 for counters, templated and installed.
What does a kitchen remodeling contractor do in Murphy TX?
A kitchen remodeling contractor in Murphy TX manages the entire remodel: demolition, framing, electrical, plumbing, drywall, paint, cabinets, countertops, tile, and appliance hookup. We pull the permits, schedule inspections, and coordinate every trade so you have one point of contact. Most Murphy projects run four to six weeks from demo to final walk.
How much does a kitchen remodeling contractor cost in Murphy?
Typical 2026 pricing in Murphy runs $18,000 to $45,000 for a full gut remodel, and $6,000 to $14,000 for a cabinet and countertop refresh. Layout changes, moving plumbing, and custom cabinetry push the number up. We give you a fixed price after a measured walk, so you are not guessing.
How to hire a kitchen remodeler in Murphy TX?
Verify the Texas general contractor license, ask for a certificate of insurance, and confirm they pull permits for structural, electrical, and plumbing work. Ask how they handle change orders and who answers your calls. We provide all of that upfront and give you a written scope before any contract is signed.
Do I need a kitchen remodeling contractor for my Murphy kitchen?
If you are moving walls, plumbing, or electrical, yes. Those changes require permits and licensed trades. If you are only swapping a faucet or painting cabinets, you do not. For a full kitchen remodel, a contractor keeps the schedule, the inspections, and the warranty in one place instead of five.
Related services
Other remodeling services we handle
general contractor near me
When your kitchen project grows into a whole-home renovation, our general contractor near me service covers framing, roofing, and structural work in Murphy. We keep the same crew and schedule so your kitchen and the rest of the house finish together.
Residential general contractor
Our residential general contractor service handles the permits, inspections, and trade coordination that a kitchen remodel requires. If your Murphy home needs a new panel to support a kitchen appliance upgrade, we fold that into the same scope.
Commercial general contractor
If you run a restaurant or office in Murphy and need a commercial kitchen build-out, our commercial general contractor team handles hoods, grease traps, and health-code inspections. Same licensed crews, different code book.Ready when you are
Get your kitchen remodeling contractor Murphy TX quote
Call (855) 948-0345 and we will schedule a measured walk-through of your Murphy kitchen. You get a fixed price, a written scope, and a start date. Licensed, insured, and serving Collin County since 2022.
Talk with the local team
Request kitchen remodeling contractor
Call (855) 948-0345 or email info@spanforgepro.com and we will get back to you the same business day. We schedule walkthroughs Monday through Friday and answer emergency calls 24/7 for storm and water damage. Tell us what you are planning and we will tell you what it takes to get it done.